For SmallHD field monitors · macOS

Calibrate to the nit.

TrueNit measures your monitor with a colorimeter, builds a 3D LUT for its calibration slot, checks its own work, and keeps every LUT and report for every monitor you own.

macOS 11 or later · Apple silicon and Intel

What it does

Everything between the probe and the SD card.

Guided monitor setup

Walks you through the monitor’s own New Calibration wizard, screen by screen, with the right answer for each one.

Closed-loop tone

Measures a grey ramp through the LUT it just built and corrects what is left, per channel.

Reports you can hand over

A self-contained HTML report scored in ΔE2000, with saturated colours scored separately so a weak corner can’t hide.

Every LUT, every monitor

Runs are kept per monitor by nickname and serial. Resume one after a restart or an SD-card round trip.

Verify any time

Check what is loaded on a monitor today against its last check, without running a new calibration.

Grading and Production

Two finals from one measurement: BT.1886 for dark grading rooms, pure gamma 2.4 for bright sets.

How a run goes

Six steps, about an hour of it warm-up.

The monitor needs a full hour on before measuring. Start it, set up, and TrueNit tells you when it’s ready.

1

Setup

Checklist, display confirmed with a magenta flash, True Tone off.

5 min
2

Seat the probe

One white and black reading to check placement.

1 min
3

Measure

White, black, primaries and three channel ramps.

~8 min
4

Build and load v1

First LUT, validated before it’s offered.

seconds
5

Refine tone

A dense grey ramp through v1, then the final LUT.

one ramp
6

Final check

Colour patches, a saturation sweep and a grey ramp through the loaded final.

then the report
Measured, not promised

Real runs on real monitors.

MonitorFlowAvg ΔE2000

November 2026, Calibrite Display Pro HL, after a full hour’s warm-up. Verified through the LUT actually loaded on the monitor.

Reading ΔE2000

ΔE2000 is how far a measured colour lands from where it should be, weighted the way eyes see. Lower is better.

  • < 1Not visible side by side. TrueNit’s target for a Standard run.
  • 1–2Visible to a trained eye on a split screen.
  • 2–3Visible to most people comparing two monitors.
  • > 3A clear colour cast.

Some colours sit outside what a panel can show. TrueNit reports those as a hardware limit before building, so they never read as a failed calibration.

Careful by default

It won’t measure when the answer would be wrong.

Each of these once produced a confidently wrong LUT. TrueNit stops before measuring instead.

What you need

A Mac, a probe, a card.

A SmallHD monitorTested on Cine 7, Indie 5 and Ultra 5.
A colorimeterCalibrite Display Pro HL is the reference. Other i1Display-class probes work.
A MacmacOS 11 or later, connected to the monitor over HDMI or SDI.
An SD cardFor moving LUTs to the monitor. One trip in Fast, two in Standard.

Know what your monitor shows.

Pricing

One price. Yours for good.

A lifetime license with every feature. No subscription.

TrueNit Lifetime license

$49once

Everything TrueNit does, for every monitor you own.

  • Unlimited monitors, runs and reports
  • Standard and Fast flows
  • Grading and Production LUTs
  • Per-monitor history and Verify
  • Apple silicon and Intel
Get TrueNit for $49

Checkout opens soon. For early access, email hello@truenit.com

Price in USD.

Questions

Which probes work?

The Calibrite Display Pro HL is the house reference. Other i1Display-class colorimeters complete a run; their numbers are their own.

Do I need ArgyllCMS?

TrueNit downloads the tested release on first launch. If you’re offline, you can install a saved copy from the Hardware tab.

Does it calibrate my Mac’s screen?

No. TrueNit is made for SmallHD monitors only and builds a LUT for the monitor’s calibration slot.

Is it a subscription?

No. You pay $49 once and keep TrueNit.

Who owns the LUTs?

You do. LUTs are plain .cube files on your Mac and on the monitor, and they work without TrueNit.

Why do two calibrated monitors still look different?

Panels differ in gamut and black level. Calibration puts both on target where they can reach it. The app explains the rest in detail.

Changelog

What’s new in TrueNit.

Each change that affects a calibration says what it was measured on.